кола за диагностика
Постинги в блога от Октомври, 2022 г.
31.10.2022 08:09 -
Free Download WinOLS 4.70 NEW Version
Obdii365.com provides free WinOLS 4.70 program for ecu programmers (kess v2, pcmtuner, kt200 etc) checksum correction.
Free Download WinOLS 4.70
Free Download WinOLS 4.70
27.10.2022 09:50 -
How to Repair Renault Bricked Clio 2 UCH?
Here is the tutorial with component identification for UCH N1 / N2 / N3 based on repair experience with these units.
Symptoms:
Symptoms:
26.10.2022 09:13 -
How to Update KT200 ECU Software using Patch?
Here is the official guide to update KT200/KTM200/ECUTuner ecu programmer software.
KT200 will prompt new version available when there is a new version. Press OK and follow steps below to run an upgrade.
KT200 will prompt new version available when there is a new version. Press OK and follow steps below to run an upgrade.
25.10.2022 09:08 -
KT200 PCB Modification
There is no 3rd revision KT200 PCB. The picture with no green pcb board was an unprocessed pcb. All devices included green small pcb (decrypt module).
So the rework will be applied to version 2 with the green small PCB on the top of ...
So the rework will be applied to version 2 with the green small PCB on the top of ...
24.10.2022 10:39 -
KT200 Read and Write Audi A4 EDC17C64 via OBD
Audi A4 B8.5 2015 2.0TDI EDC17C64 KT200 ecu programmer automatically virtual read 10 seconds without problem.
VIRTUAL READ + write OBD. write/checksum – ok, no problem 10 min.
100% honest and sure. Virtual read 100%, compared fil...
VIRTUAL READ + write OBD. write/checksum – ok, no problem 10 min.
100% honest and sure. Virtual read 100%, compared fil...
20.10.2022 09:12 -
Mercedes Benz CRD3 checksum bypass via Vediamo
This is common on Mercedes Benz crd3p.b0, crd3p.e1 and other crd3 ECUs. After writing file with wrong checksum, car start but only once, after you turn ignition off and on it’s continuously off and on 87 kl. relay.
To fix thi...
To fix thi...
19.10.2022 09:41 -
CG FC200 Adds GM ACDelco ZF 9HP and More MG1 ECUs
CG FC200 ECU programmer released new software version 1.0.9.0 on Oct. 19th 2022.
CG FC200 Software V1.0.9.0 NEW
CG FC200 Software V1.0.9.0 NEW
18.10.2022 06:07 -
KT200 GM Opel Delco E98 ECU Bench Pinout
Does KT200 ecu programmer read and write GM/Opel Delco E98 ECU? and if yes how it reads boot, OBD or bench?
Yes, KT200 does Delco E98 without problem. Bench mode is recommended and it is faster. Some users also tested working in OB...
Yes, KT200 does Delco E98 without problem. Bench mode is recommended and it is faster. Some users also tested working in OB...
17.10.2022 11:40 -
KT200 Read and Write Bosch EDC17CV41 on Bench
Here is the guide to read BOSCH EDC17 CV41 [ 1797 ] - [Diesel] Challenger, Claas, Isuzu, Iveco, JCB, Man, Massey Fergusson, New Holland, Valtra ECU with KT200.
CV41 has 2 possible S1 S2 pinouts for GPT. Connect the multi-function cable ...
CV41 has 2 possible S1 S2 pinouts for GPT. Connect the multi-function cable ...
13.10.2022 10:11 -
Yanhua ACDP MSV80 MSV90 MSD8x by OBD or Bench Mode
There are three ways to read BMW MSV80 MSV90 MSD85 MSD81 MSD80 etc DME ISN with Yanhua Mini ACDP,
Open DME shell to read ISN
OBD/CAN mode
Open DME shell to read ISN
OBD/CAN mode
12.10.2022 10:34 -
How to Read and Write Renault Truck MS6.3 ECU by KT200?
New test feedback: Renault Premium truck 420 dCi common rail engine with ecu Bosch MS6.3 read and write OK with KT200 full ecu programmer.
Select Driver : Truck OBD – Renault MS6.3
Search pinout under manual
Select Driver : Truck OBD – Renault MS6.3
Search pinout under manual
11.10.2022 09:00 -
CGDI MB and CG Pro Solve Benz W639 W636 No Show Mileage
Symptoms:
It is a common phenomenon that Mercedes Benz Vito/Viano, W636/W639 doesn’t show mileage at all after replacing second-hand instrument cluster.
Cluster (new type ) Eeprom: 25LC640 (25640)
It is a common phenomenon that Mercedes Benz Vito/Viano, W636/W639 doesn’t show mileage at all after replacing second-hand instrument cluster.
Cluster (new type ) Eeprom: 25LC640 (25640)
Търсене
За този блог
Гласове: 20
Блогрол